大猩猩環氧樹脂膠
Directions
Gorilla at Work
Related Products
FAQs

大猩猩環氧樹脂膠

強韌,透晰,超強力

大猩猩將環氧樹脂帶到了一個新的水平- 大猩猩強韌程度。 憑藉其卓越的耐溶劑性和防水性,大猩猩環氧樹脂膠具有令人難以置信的堅固性和耐用性,適用於家居和汽車維修。 易於使用的注射器將樹脂和固化劑分開,因此易於分配,且不會隨著時間而硬化。 這種由兩部分組成的間隙填充配方可輕鬆粘合鋼,鋁,木材,陶瓷,瓷磚和大多數塑料。 此外,它乾固後的表現,如水晶般清晰,使項目看起來一塵不染。

 

 

壓緊時間:30分鐘//打開時間:5分鐘

 

待乾時間:24小時//待乾顏色:清晰

 

完全乾固:24小時

MSDS

大猩猩環氧樹脂膠 Directions

大猩猩環氧樹脂膠用法

  1. 準備工作區域和表面

如果您是第一次使用大猩猩環氧樹脂膠,或粘接新型材料,我們建議您首先使用測試件嘗試。

 

準備工作區域:建議在通風良好的區域使用。確保您的工作區域免受溢出影響。收集攪拌盤和攪拌棒,以便將所有物品放在一起。

 

準備表面:為了提高附著力,使用前先讓表面變得光滑。然後清潔並抹乾所有要粘合的表面。

 

  1. 混合大猩猩環氧樹脂膠

從兩個注射器上取下黑色蓋子。尖端朝上,從注射器尖端切走端部。尖端仍然指向上方,確保通過柱塞來消除兩邊空氣,直到樹脂和硬化劑都在尖端處。

 

推動柱塞,將樹脂和固化劑均勻分配到干淨的一次性表面上。包裝本身可用作混合托盤。如果將塑料泡罩殼翻轉過來,可以使用小井作為啟動盤開始分配,直到樹脂和固化劑均勻流動。一旦流量均勻,移動到較大的混合井,以分配均勻比例。

 

將兩部分混合約20秒,直至混合物均勻。在5分鐘內進行。

 

當你混合時,你會注意到環氧樹脂變暖了。這是樹脂和硬化劑結合時發生的反應。

 

  1. 應用

混合完成後,在5分鐘內塗抹大猩猩環氧樹脂。環氧樹脂混合物會繼續變稠,粘合強度會隨著等待施加時間的延長而降低。

 

  1. 夾緊

為了達到最大的粘合強度,將工件夾緊在一起並保持不受干擾。

 

重要的處置時間

設置:5分鐘施加和定位

 

處理:不受干擾地固化30分鐘(無重量或處理)

 

最終固化:承重24小時

 

儲存:要關閉,請稍微拉回柱塞。用乾布擦拭吸頭,並在尖端和蓋子上對齊凹口。緊緊地關上。

 

請訪問我們的常見問題解答,了解有關Gorilla Epoxy將粘合的表面,清理信息等的更多信息。

Gorilla At Work

Want to see how tough our products are? Watch the videos below to see them in action.

大猩猩環氧樹脂膠®FAQs

What surfaces will Gorilla Epoxy bond?

Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more!

What surfaces will Gorilla Epoxy bond?

Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®.

What is the shelf life? Are there storage tips to extend the shelf life?

Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix.

How do I remove Gorilla Epoxy?

Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding.

Uncured Removal:

Skin:Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps.
Hair: Isopropyl alcohol
Clothes and Carpet:Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric.

What is the best application temperature?

For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time.

Gorilla Epoxy’s cured bond withstands temperatures ranging from -10° to 180°F.

Do I need to use clamps with Gorilla Epoxy? How long?

Clamps are recommended for use during setup to ensure the bond sets correctly.

Set Time: 5 minutes to mix, apply and position
Handling Time: Leave 30 minutes undisturbed (clamping is recommended)
Full Cure Time: 24 hours for load-bearing weight

How much Gorilla Epoxy do I apply?

Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond.

Average coverage from our 25 mL epoxy syringe will cover 100 square inches.

What can I use as a mixing tray or stir stick?

A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing.

How do I dispense Gorilla Epoxy?

Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from tip of syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.

What is Gorilla Epoxy?

Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results.

Is Gorilla Epoxy gap filling?

Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight.