大猩猩膠水
Directions
Gorilla at Work
Related Products
FAQs

大猩猩膠水

堅固,澎漲,可黏合任何物件的膠水

Gorilla 膠水內的泡沫會在凝固後膨脹3倍,只需用0.5安士的膠水便可黏合1平方呎的面積。用途廣泛,適用於一般家居內外修復、維修及創意項目。可黏合木材,石材,金屬,陶瓷,發泡膠,玻璃,瓦磚,水泥等其他無數物料!100%防水,在潮濕環境下亦能保持良好黏力。耐冷耐熱,在極熱或極冷的環境下亦不受影響!可上漆、染色、打磨,容易達至最終的理想效果。

產品選擇

Gorilla 膠水3g 4支裝.2安士. 4安士. 8安士. 18安士. 36安士.

夾合時間: 1-2 小時// 黏合時間: 10-15 分鐘

乾透時間: 1-2小時達80% // 乾透顏色: 淺啡色

完全固化: 24小時

Safety Data Sheets

大猩猩膠水 Directions

1.    準備噴濕要黏合的表面

如果您第一次使用大猩猩膠水,或黏合的一種新型材料,我們建議你在一小部分位置測試一下。

準備好黏合的表面:所有表面必須清潔,無灰塵和緊密。有光澤的表面,例如金屬,玻璃和某些塑料,可擦拭去粗化表面,讓膠水得以滲入。

噴濕表面:用水略微濕一下表面。我們建議您使用濕布或水噴霧。不要過量。對於緊密的硬木,也可以輕輕噴濕黏合的兩面。

 

2.    均勻塗抹大猩猩膠水在乾燥表面

黏合:小心地把膠水塗在乾燥的表面上。不要過度使用。我們建議戴手套或用即棄的刷掃。在一些情況下,大猩猩膠水可能會引起皮膚過敏。如果您皮膚敏感,請採取額外的預防措施。

如果膠水黏著你的皮膚,可嘗試用乾布或紙巾先抹掉(特別是如果膠水仍未凝結)。如果還是不行,請嘗試用肥皂水洗滌,或使用刮刷去除。抹乾你的皮膚和使用潤膚液。我們不建議使用任何形式的酒精或丙酮,因為會去掉皮膚上的天然油份,而膠水有可能更黏著皮膚表面。

 

3.    夾緊兩個黏合表面

夾住:確保夾的壓力均勻分佈在表面。如果你沒有夾子,用重物壓住或大猩猩膠帶®綁住兩面。對於較輕的物件,請嘗試使用橡皮筋緊緊聯繫在一起。夾合時間1-2小時。為了達到最佳效果,待24小時完全夾緊。

 

4.    擦淨

如果您需要去除未固化的膠水或“擠”出來的膠,我們建議用乾布擦拭,或使用標準的油漆稀釋劑。如果使用油漆稀釋劑,請務必閱讀指示,戴手套。如果膠水乾涸,最好清除方法:嘗試打磨、鑿、刮或拔起。乾涸的膠水不會損壞工具。

 

5.    儲存貼士

每次使用後,用清潔的布擦拭瓶蓋和噴嘴。請把2安士大猩猩膠,用清潔的布擦乾淨瓶蓋和噴嘴,然後存放在陰涼,乾燥的地方。4安士大猩猩膠,我們建議擠出瓶子多餘的空氣,緊閉瓶口,然後放在陰涼,乾燥的地方,有一年的保質期。

Gorilla At Work

Want to see how tough our products are? Watch the videos below to see them in action.

大猩猩膠水®FAQs

What is the temperature range for applying the glue?

For best results, apply the glue at room temperature.

Original Gorilla Glue should be left out of reach of children and animals.

For general inquiries or first aid tips, contact the Gorilla Support Team at +852-2967-0202 (Monday–Friday, 9 a.m.– 6 p.m.).

Can you speed up the curing process?

Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials.

Is Gorilla Glue truly 100% waterproof?

Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II.

How do I extend the shelf life of Gorilla Glue?

Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid.

My bottle of glue has formed a dry layer on top; can I still use it?

Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap.
Do not microwave or heat your bottle of Gorilla Glue to soften the top layer.

How do I clean up Gorilla Glue?

Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper

What is the proper clamp time?

When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight.

What if I don’t have clamps?

Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure.

How much Gorilla Glue should I apply?

Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools.
Visit our Gorilla Glue Directions page for more information.

Why do I need to add moisture before gluing with Gorilla Glue?

Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing.

Do I need to prepare the surface first?

Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip.

Is Gorilla Glue really for the Toughest Jobs on Planet Earth?

Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.