大猩猩木材專用膠4安士裝
Directions
Gorilla at Work
Related Products
FAQs

大猩猩木材專用膠4安士裝

強力、不會起泡、乾透後呈天然木材顏色

大猩猩木材專用膠是木匠,木工和愛好者的信心之選。大猩猩木膠是聚乙烯醇膠水,易於使用,水融性膠水,黏力特強。防水、乾透後呈天然木材顏色,可上漆。

 

產品選擇

4安士. 8安士. 18安士

夾合時間: 20-30分鐘 // 黏合時間: 5-10 分鐘

乾透時間: 1-2小時達80% // 乾透顏色:天然木材顏色

完全固化: 24小時

m.ecommerce.product.lbl.SDS

大猩猩木材專用膠4安士裝 Directions

大猩猩木材專用膠使用方法

  1. 應用

    為了達到最佳效果,這是至關重要的木材表面膠水施用前製備。對於覆膜,表面光滑,使板面痕,撕裂斯奈普斯免費同時,應注意避免拋光和結束斯奈普斯到底有多少猩猩木膠適用取決於許多因素一般情況下,適用於表面之一大方量難以樹林,應用兩個表面上的膠水。與其他表面一起兩個表面上均勻分佈的粘合劑。足夠的膠水應採用使擠壓夾緊發生覆蓋範圍:1加侖猩猩木膠將覆蓋約200平方英尺。1液體盎司將覆蓋大約160平方英尺。

  2. 夾緊

    技術和夾具所使用是由許多因素決定類型特定類型的聯合類型的股票木材,股票含水量,室溫,組裝時間和表面質量一般情況下,施加足夠的壓力,這將導致膠水適當的壓力時,擠出

    阻斷時間時間壓力量需要保持施用20-30分鐘,室溫下的應用程序。溫度必須高於55°F注意,夾緊時間可以依賴於溫度,濕度,以及木材的孔隙率。

    固化時間時間達到粘接強度:24小時

  3. 清潔

    清理膠水是濕的:用乾淨的濕布擦掉多餘的膠水根據需要用布的潔淨區,除去所有的膠水使盡可能多的通行證。地區已經完全乾燥需要沙子。洗手皮膚和肥皂和溫水濕布然後用清水沖洗


    清理時,膠水已幹用鋒利的油灰刀,剃須刀,或鋒利的刮刀根據需要表面硬化然後沙子。浸泡手和皮膚肥皂和溫水洗淨,再用清水洗淨。

    清潔提示:使用乾淨的濕布收盤擦掉多餘的膠水如果噴嘴變得膠水堵塞取下瓶蓋,並用牙籤向後重物然後用溫水沖洗乾淨

    手拔猩猩木膠,用溫水肥皂和水

Gorilla At Work

Want to see how tough our products are? Watch the videos below to see them in action.

大猩猩木材專用膠4安士裝®FAQs

Is there any way to remove Gorilla Wood Glue from carpet and/or fabric?

Once dried, it is very difficult to remove Gorilla Wood Glue. If the glue is still wet, adhesive can be removed with water.

Please keep in mind, this response is for Gorilla Wood Glue, a water-based PVA. If you are looking for information for removing Original Gorilla Glue, please click here.

How can I prevent creep?

The best solution to minimize creep is to make sure the wood species being joined are the same species and moisture content to start. When gluing, orient the grain in the same direction. For more information on glue creep, click here.

How can I prevent stepped joints?

The best solution for stepped joints is to make sure the wood pieces being joined are of the same moisture content. After gluing, wait for moisture around the joint to evaporate before planing or sanding. The length of time to wait depends on air circulations, temperature, relative humidity around the panel, amount of water added by the glue and wood species. Generally, seven days is sufficient.

Can I disassemble a glue joint?

Once cured, it is virtually impossible to disassemble a Gorilla Wood Glue joint without damaging the surfaces.

Can Gorilla Wood Glue be used in steam bending wood and laminating?

Yes. The substrates need to be steam bent and dried first to prevent creep or stepped and sunken joints.

Can Gorilla Wood Glue be used in spraying applications?

Yes, but depending on the spraying equipment, the viscosity of Gorilla Wood Glue may need to be lowered with water (not to exceed 5% by weight).

Can Gorilla Wood Glue be applied with a syringe?

Yes. The viscosity of Gorilla Wood Glue will allow it to be injected using a glue syringe applicator.

Please note that this answer is regarding Gorilla Wood Glue, which is a water-based PVA. We do not recommend using Original or White Gorilla Glue in a syringe application, as it has a higher viscosity.

Can I change the viscosity of Gorilla Wood Glue?

Gorilla Wood Glue, unlike Original Gorilla Glue, is a water-based adhesive. You can thin Gorilla Wood Glue by adding water (not to exceed 5% weight).

Original Gorilla Glue foams as it cures. Does Gorilla Wood Glue foam?

Gorilla Wood Glue is a water-based polyvinyl acetate (PVA) and will not foam as it dries.

Original Gorilla Glue, however, does expand 3–4 times the amount that you apply.

Will Gorilla Wood Glue adhere to stained or painted items?

Gorilla Wood Glue will work on stained surfaces. However, if the surface has been painted or sealed with a sealer, urethane, varnish or shellac, Gorilla Wood Glue will not adhere to it.

Can heat be used to break the glue bond?

Gorilla Wood Glue is very heat resistant. Once cured, it is safe to heat up to 150°F.

What does solvent resistance mean?

Solvent resistance means that once cured, Gorilla Wood Glue’s strength and consistency are not compromised by exposure to most solvents, such as paint thinners.

What is ANSI/HPVA Type II water resistance?

ANSI/HPVA has set up criterion for determining different levels of water resistance for plywood.Type I rating means the bond is waterproof.
Type II rating means the bond is water resistant.

Gorilla Wood Glue passes ANSI/HPVA Type II, while Original and White Gorilla Glue® passes Type I.

What makes Gorilla Wood Glue different than other wood glues that are currently available?

Gorilla Wood Glue is incredibly strong and bonds faster. It requires just 20–30 minutes of clamping.
In addition, Gorilla Wood Glue dries a natural color for a professional finish. No more orange “after-glow.”