大猩猩膠8安士裝
Directions
Gorilla at Work
Related Products
FAQs

大猩猩膠8安士裝

堅固,澎漲,可黏合任何物件的膠水

HKD 174.00

始於這一切的產品。大猩猩膠水以其令人難以置信的工業握持力和多功能性而聞名。 水活化後,它延伸成各種材料,與幾乎所有物體都難以置信的牢固結合。 大猩猩膠水是幾乎任何項目或維修的解決方案。 它具有100%的防水性能,可在室內和室外使用,並且堅固到足以抵禦各種惡劣環境。 另外,它的膨脹性使其可以穿透膠粘表面,從而形成優異的粘結力。 對其進行打磨,油漆,染色。 簡而言之,這是地球上最堅韌的膠水。
 
夾緊時間:1-2小時//開放時間:10-15分鐘
 
乾燥時間:1-2小時內達到80%//乾固顏色:淺棕褐色
 
完全乾固:24小時
MSDS

大猩猩膠8安士裝 Directions

  1. Prepare and Dampen the Surfaces

    If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. To open a bottle larger than 2 ounces, cut the tip of the nozzle where it comes up to a point and starts to indent. The cap is attached to the side of the nozzle.

    Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.

    Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.

  2. Evenly Apply Gorilla Glue Onto the Dry Surface

    Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.

    If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.

  3. Clamp the Two Surfaces Together Tightly

    Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.

  4. Clean up

    If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools.

  5. Storage Tips

    After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle.

Gorilla At Work

Want to see how tough our products are? Watch the videos below to see them in action.

大猩猩膠8安士裝®FAQs

Why do I need to add moisture before applying Gorilla Glue?

Gorilla Glue is a moisture activated polyurethane adhesive, therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing.

How much Gorilla Glue should I apply?

Apply a thin layer of glue. Gorilla Glue expands up to 3 times so little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture.

How do I remove Gorilla Glue from my body or skin?

It is strongly recommended that gloves are worn during application. If you do get Gorilla Glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol, acetone, or other solvent.